Fiat 500X, Tipo, Egea BCM Delphi
Memory device is NEC uPD70F3556.
You can read NEC data flash and program key by OBD2 with VagTacho K+CAN with Fiat activation or with UPA-S, download connection diagram.
Expected file size is 32768 or 65536 bytes.
Software shows 5-digit PIN code.
Use original Fiat remote key with Megamos Crypto 128-bit AES ID88 transponder. Remote part is also programmed and is operating.
Programmed key must be matched with car using diagnostic device.
Fiat
Software module 221
Vehicles equipped with this unit:
Fiat:500X, Tipo, Egea
Jeep:Renegade
Software module 202
Fiat BSI Continental type 2. Memory device is Motorola 9S12XEG384.
You can read and write Motorola 9S12XEG384 with TMPro. Download connection diagram
Expected file size is 4096 bytes.
Software shows 5-digit PIN code.
Use HITAG 128-bit AES remote key ot PCF7939MA transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Fiat:500X
Software module 201
Fiat BSI Continental type 1. Memory device is Motorola MPC5606B.
You can read and write Motorola MPC5606B with UPA-USB-S programmer. View connection diagram
Expected file size is 65536 bytes. Software shows 5-digit PIN code.
Use HITAG 128-bit AES remote key ot PCF7939MA transponder.
Written remote key or transponder are ready programmed to start car.
REMOTE part of remote key is also programmed and work.
Vehicles equipped with this unit:
Fiat: Uno (chassis F), Mobi, Toro
Software module 194
Fiat South America immobox Marelli IMM009.10
Memory device is Motorola 9S08DZ32 32-pin SMD package.
You can read Motorola with TMPro, download connection diagram. Software shows 5-digit PIN code.
Use Megamos Crypto or Silca T6 – JMA TP08 or TS48 or CN6 or KD48 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Fiat: Fiorino Furgao, Palio 2012->, Siena 2012->, Ducato 2012->
Peugeot: Boxer 2012->
Citroen: Jumper 2012->
Software module 175
Fiat Grand Siena, Palio BSI Marelli type 5 with ID46. Memory device is serial eeprom 95c160 or 95c640 SSOP8 package.
Expected file size is 2048 or 8192 bytes. Use PCF7936 or Silca T14 – JMA TP12 or CN3 transponder or remote key with PCF7946.
IMPORTANT when you want to program remote key :open key and look on PCB.
You will find 2 SMD chips – PCF7946 (SMD 14 pins) and smaller SMD chip, which can be with 8, 10, or 16 pins.
If smaller SMD chip is with 10 or 16 pins, PROGRAM KEY AS TYPE 1.
If smaller SMD chip is with 8 pins, PROGRAM KEY AS TYPE 2.
IMPORTANT:if buttons of remote operate, but not work properly, for ex. button for locking opens trunk, this is NOT A TMPro SOFTWARE PROBLEM. Use other type remote.
Software shows 5-digit PIN code.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Fiat:Grand Siena (2011-), Palio (2011-), Ducato(2011-), 500L(2011-)
Alfa Romeo:Giulietta(2011-)
Iveco:Daily(2011-)
Software module 163
Suzuki engine ECU with ID46 Memory device is serial eeprom 93c56 or 93c66 both SMD8 package.
For 93c56 expected file size is 256 bytes,for 93c66 is 512 bytes.
Use Philips PCF7936 – Silca T14 – JMA TP12 or CN3 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Suzuki:Swift(2007-), Splash(2007-), Grand Vitara(2007-)
Fiat:Sedici
Software module 118
Alfa Romeo, Fiat key reader TEG
Memory device is serial eeprom 24c04 SMD8 package.
Expected file size is 512 bytes.
Software shows 5-digit PIN code.
Use PCF7936 or Silca T14 – JMA TP12 or CN3 transponder or remote key with PCF7941.
Written transponder or remote key is ready programmed to start car.
Remote is also ready to operate ,no need OBD2 programming.
NOTE:Remote part will work 100% ONLY if key is unlocked with TMPro! If your key is unlocked, but you don`t know if it was unlocked using TMPro – unlock it with TMPro again, download connection diagram
NOTE:Your key can be 2 different types – with PCF7341 and with PCF7941. At reading of key TMPro will show PCF7941 for both types.
Look here to determine correct type of PCF in your key.
Vehicles equipped with this unit:
Alfa Romeo: 159, Brera, Spider
Fiat: Croma
Software module 112
Fiat, Lancia, PSA BSI Marelli type 3.
Memory device is serial eeprom 95c160 SSOP8 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 – JMA TP12 or CN3 transponder or remote key.
IMPORTANT when you want to program remote key :open key and look on PCB.
You will find 2 SMD chips – PCF7946 (SMD 14 pins) and smaller SMD chip, which can be with 8, 10, or 16 pins.
If smaller SMD chip is with 10 or 16 pins, PROGRAM KEY AS TYPE 1.
If smaller SMD chip is with 8 pins, PROGRAM KEY AS TYPE 2.
IMPORTANT: if buttons of remote operate, but not work properly, for ex. button for locking opens trunk, this is NOT A TMPro SOFTWARE PROBLEM. Use other type remote.
Software shows 5-digit PIN code.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Fiat: Bravo(2007-), Ducato(2006-), Stilo(2007-), Punto(2007-), Idea(2008-)
Citroen: Jumper(2006-), Relay(2006-)
Peugeot: Boxer(2006-)
Lancia: Ypsilon(2007-), Musa(2007-)
Software module 100
Fiat dashboard Marelli, VDO Memory device is serial eeprom 95c160 or 24c16 both SMD8 package. Expected file size is 2048 bytes. Use Megamos Crypto or Silca T6 – JMA TP08 or TS48 or CN6 or KD48 transponder. Software shows PIN code. For Marelli dashboard written transponder is ready programmed to start the vehicle. For VDO dashboard transponder has to be matched with car using diagnostic device. VagTacho K+CAN supports key programming for Fiat dashboards, please visit VagTacho K+CAN
Vehicles equipped with this unit:
Fiat: Palio, Siena, Strada, Uno 2010
Software module 59
Fiat Grande Punto BSI Delphi. Memory device is serial eeprom 93c86 SMD8 package or NEC MCU. For serial eeprom 93c86 expected file size is 2048 bytes. You can read Fiat BSI by OBD2 using Immo tool with Fiat software activation. For files read by OBD2 expected size is 21 or 32768 or 65536 bytes. Use PCF7936 or Silca T14 – JMA TP12 or CN3 transponder or remote key with PCF7946. Software shows 5-digit PIN code. Written transponder is ready programmed to start the vehicle.
Note: for files read by OBD2 from NEC MCU software shows PIN code and prepares keys but does not create new file. You must program prepared keys by OBD2 and PIN code.
IMPORTANT when you want to program remote key :open key and look on PCB.
You will find 2 SMD chips – PCF7946 (SMD 14 pins) and smaller SMD chip, which can be with 8, 10, or 16 pins.
If smaller SMD chip is with 10 or 16 pins, PROGRAM KEY AS TYPE 1.
If smaller SMD chip is with 8 pins, PROGRAM KEY AS TYPE 2.
IMPORTANT: if buttons of remote operate, but not work properly, for ex. button for locking opens trunk, this is NOT A TMPro SOFTWARE PROBLEM. Use other type remote.
Vehicles equipped with this unit:
Fiat: Grande Punto, New 500, Fiorino
Alfa Romeo: Mito
Ford: KA
Citroen: Nemo
Peugeot: Bipper
Opel: Combo D