Yamaha Majesty 125 engine ECU
Memory device is serial eeprom 93c56 8-pin SMD package.
Expected file size is 256 bytes.
Use TMPro chip or K-JMD transponder.
Written transponder is ready programmed to start vehicle.
Yamaha
TMPro - Yamaha Keyless - PIN Code
PIN Code for Yamaha Motorbikes Keyless / Proximity system
THIS CODE IS NOT AVAILABLE FORM ANY DEALER
DEALER SOLUTION IS TO REPLACE 2 UNITS IN THE BIKE + A NEW KEY
Send us your file from Yamaha keyless start unit or steering lock unit and you will get 6-digit PIN code.
This code is required for learning a new key or for an emergency start.
We support all Yamaha keyless-go bikes
Memory device is 24c02 or 24c04. You can read this with TMPro.
Procedure:
- Read 24c02 or 24c04 - then send BIN file to admin@remotekeys.co.uk
- We will send back to you the 6-digit PIN code
Vehicles equipped with this unit:
Software module 108
Software module 108 – Yamaha bikes immobox Moric type 2.
This is new variant of Yamaha immobox, where there is no serial eeprom S29190.
On place, where you must find serial eeprom S29190, you find 16-pin chip TMS3705.
Keys ARE NOT in this chip TMS3705!
Memory device is MORIC MCU 30 pins SSOP package.
MORIC MCU in this immobox IS NOT POSSIBLE TO READ!
Programming of MORIC MCU is thru TMPro, view connection diagrams and instructions.
Use TMPro chip or Yamaha key or Texas Crypto – Silca 4D-60 – JMA TP06/TP19 transponder.
Written transponder is ready programmed to start bike.
Also you can set immobox to virgin state.
IMPORTANT NOTE:you can program ONE MASTER key and ONE SLAVE key.If you want more slave keys, program a slave key and clone it with software 65.For cloning Yamaha keys with software 65 JMA TPX cloner is not needed.
IMPORTANT NOTE:If you want to program MASTER key, you also MUST MAKE ECU VIRGIN, because programming of MASTER key will delete synchronisation IMMO-ECU.
Here is key programming procedure:
- Make connections like at connection picture using cable with 8 striped wires.Gray wire is not used.Connect other end of cable to TMPro box.
- Run soft TMPro.exe.
- Select manually software module 108
- Put in box blank 4D-60 chip or original Yamaha key
- Press PROG,select SLAVE key,OK and job done in 2 seconds.
If ECU and IMMO are not MATCHED pair (do not originate from one and same bike) procedure is:
- Program MASTER KEY to immobox.
- Take picture of ECU and send to me.
- I will send you picture with eeprom location.
- You read eeprom and send file to me.
- I make file virgin and send to you.
- You write new file into eeprom.
- You fit in bike ECU and IMMO.
- 8.At first ign ON with MASTER KEY code from IMMO is sent to ECU.
Job done.
Connection diagrams
Vehicles equipped with this unit:
Yamaha: R1, T-MAX, R6, BT1100, FJR, FZR, FZ1, FZ6, FZS, XT, XJR, XTR, XTX, XVX
Software module 90
Yamaha scooter ECU Mitsuba
Memory device is serial eeprom 24c04 SMD8 package.
Expected file size is 512 bytes.
Use TMPro chip or T5 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Yamaha:X-MAX 125
Software module 66
Yamaha bikes immobox Moric
Memory device is serial eeprom Seiko S29190 SMD8 package.
Eeprom can be located in 2 different position. Click here and here to see where to dig for to reach eeprom.
Expected file size is 128 bytes.
Use TMPro chip or K-JMD transponder.
Written transponder is ready programmed to start bike.
Note: latest Yamaha immobox Moric DO NOT HAVE serial eeprom, so please check your immobox before purchasing this software. If there is no serial eeprom,but 16 pin chip TMS3705 you need software module 108.
Vehicles equipped with this unit:
Yamaha: BT1100, FJR, FZR, FZ1, FZ6, FZS, XT, XTR, XTX, XVX, YZF
MBK: Skycruiser 125