Software modules description
Here you can find information for every software module - what memory device have to read from immobox, expected lenght of readed file, what transponder have to be used, is transponder ready to start car or have to be matched using diagnostic device and PIN code. Some modules like 30,31,36,39,44,57,102,103,146,152 do not need files or they can be used in 2 ways - with or without file information.
Fiat, Lancia, Peugeot, Citroen BSI Marelli type 3
Memory device is serial eeprom 95c160 or 92c320 SSOP8 package.
Expected file size is 2048 or 4096 bytes.
Use TMPro chip or PCF7936 transponder or remote key.
IMPORTANT when you want to program remote key :open key and look on PCB.
You will find 2 SMD chips – PCF7946 (SMD 14 pins) and smaller SMD chip, which can be with 8, 10, or 16 pins.
If smaller SMD chip is with 10 or 16 pins, PROGRAM KEY AS TYPE 1.
If smaller SMD chip is with 8 pins, PROGRAM KEY AS TYPE 2.
IMPORTANT: if buttons of remote operate, but not work properly, for ex. button for locking opens trunk, this is NOT A TMPro SOFTWARE PROBLEM. Use other type remote.
Software shows 5-digit PIN code.
Written transponder is ready programmed to start the vehicle.
aewoo, Chevrolet immobox ID48
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use TMPro chip or Megamos Crypto or TS48 transponder.
Written transponder is ready programmed to start car.
Mitsubishi immobox ID46
Memory device is serial eeprom 24c01 SMD8 package.
Expected file size is 128 bytes.
Use TMPro chip or PCF7936 transponder.
Written transponder is ready programmed to start car.
Chevrolet BSI Siemens
Memory device is Motorola MC68HC705B32 52 pin PLCC package.
Expected file size is 256 bytes.
Use TMPro chip or K-JMD transponder.
Written transponder is ready programmed to start car.
Isuzu immobox SiemensVDO
Memory device is serial eeprom 93c56 or 93c66, both SMD8 package.
Expected file size is 256 or 512 bytes.
Software shows PIN code.
Use TMPro chip or PCF7936 transponder.
Written transponder is ready programmed to start car.
Chevrolet, Opel immobox ID46
Memory device is serial eeprom 95c040 SMD8 package or Motorola 9S08DZ60 QFP32 package.
Expected file size is 512 or 1024 bytes.
Use TMPro chip or PCF7936 transponder.
Written transponder is ready programmed to start car.
Alfa Romeo, Fiat key reader TEG
Memory device is serial eeprom 24c04 SMD8 package.
Expected file size is 512 bytes.
Software shows 5-digit PIN code.
Use TMPro chip or PCF7936 transponder or remote key with PCF7941.
Written transponder or remote key is ready programmed to start car.
Remote is also ready to operate, no need OBD2 programming.
NOTE: Remote part will work 100% ONLY if key is unlocked with TMPro! If your key is unlocked, but you don`t know if it was unlocked using TMPro – unlock it with TMPro again, view connection diagram
NOTE: Your key can be 2 different types – with PCF7341 and with PCF7941. At reading of key TMPro will show PCF7941 for both types. To determine correct type of PCF in your key.
NOTE: Software supports also file read from Motorola in BSI, but in this case you must program key by OBD2 for to start car and activate remote. BSI can be read by OBD2 ONLY when there is valid key i.e. job is “Make Spare key”. If ALL KEYS ARE LOST you must remove BSI and read Motorola by testpoints, view connection diagram.
Look here to determine correct type of PCF in your key.
Gilera, Piaggio bikes engine ECU EFI
Memory device can be ST72c334 QFP64 package or serial eeprom 25c080 SMD8 package.
To see where keys are stored, check eeprom:
– If eeprom is 25c040, keys are in MCU ST72c334.
– If eeprom is 25c080, keys are in eeprom.
Reading of ST72c334 MCU is thru TMPro interface.
Expected file size for ST72c334 is 256 bytes, for 95c080 is 1024 bytes.
Use TMPro chip or T5 transponder.
Written transponder is ready programmed to start bike.
KTM bikes immobox ZADI
Memory device is serial eeprom 24c04 SSOP8 package.
Expected file size is 512 bytes.
Use TMPro chip or K-JMD transponder.
Written transponder is ready programmed to start bike.
BMW, Mini CAS SiemensVDO
Memory device is Motorola MCU 912DG256 or 9S12DG256 or 9S12XDP512
Expected file size is 2048 or 4096 bytes.
IMPORTANT NOTE: Motorola MCU is locked, not possible to read/write with TMPro.
If job is ALL KEYS LOST and you get message that file is CAS3+:
– if ISN is 16 bytes you need eeprom file read from engine ECU.
– if ISN is 2 bytes it is not possible to make key with TMPro.
If job is SPARE KEY – in all cases you need just CAS file.
For ECU with MPC556 MCU you must read external eeprom 95c640.
For ECU with TRICORE MCU you must read eeprom from TRICORE.
Use TMPro chip or PCF7936 transponder or remote key.
Written transponder or remote key is ready programmed to start car.
To activate remote: insert key to turn ignition ON. Remove key. Press any button few times. Repeat these steps till remote starts to work.
If you have got locked CHINESE BMW HITAG2 remote keys, you can UNLOCK them and set as BRAND NEW so you can use them again with any car.
